PGJ Rotary Sprinklers
PGJ-06

Pop-Up Height: 6"
Overall Body Height: 9 1/8"
Exposed surface diameter: 1 1/8"
Bottom: ˝" female inlet NPT
Note: If the overall height of spray head is too tall for your application; you can use a Hunter Pre-Made Swing Joint to move the head off the pipe and allow you to bury it deeper.
 

All the features and benefits of the PGP®, scaled down to fit typical spray applications.

A rack of easy-to-install-and-change, water-efficient nozzles…just like PGP. Easy adjustment from the top of the sprinkler…just like PGP. The safety and durability of a rubber cover…just like PGP. The PGJ is a chip off the ol’ block, in essence a PGP “junior.” Hunter has scaled down the world’s top-selling sprinkler exclusively for use in applications that typically call for a spray but where it’s now possible to have all the benefits of a sprinkler rotor. The PGJ is capable of working in tandem with larger sprinkler rotors to combine big and small areas in a single zone, offering a convenience and efficiency that sprays do not. With PGJ, fewer sprinkler heads perform more efficient work for a more economical price.

Features and Benefits

Radius adjustment screw
Allows fine tuning of spray; ensures positive nozzle retention; can't be lost

Protective rubber cover
Keeps debris out

40°– 360° adjustable arc
Easily adjustable from top of sprinkler; up; down; wet or dry

Water-lubricated gear drive
Time proven; reliable rotation; year after year

Variable stator
Keeps rotation speed consistent regardless of nozzle size or pressure

Extra large filter screen
Traps more debris without clogging

Sprays? Or Time-Saving, Money-Saving, Water-Saving Rotors?

When your landscape has mid-range zones that are long and narrow; the obvious choice would be to install sprays. Yet, the intelligent choice would be a sprinkler rotor specifically designed to fit this kind of landscape. With the scaled-down-in-size PGJ; two rows of sprinkler rotors can do the same job as three rows of spray heads. Because PGJ sprinkler rotors can run on the same zone as other rotary sprinklers; they require fewer irrigation valves and stations; and; in turn; less trenching; piping and labor. It all adds up to less installation time and lower installation costs (as well as lower watering costs).

PGJ Models

PGJ-00 – Shrub
PGJ-04 – 4" Pop-up (10 cm)
PGJ-06 – 6" Pop-up (15 cm)
PGJ-12 – 12" Pop-up (30 cm)

Dimensions

• Overall height:
  PGJ-00 – 7" (18 cm)
  PGJ-04 – 7 1/8" (18 cm)
  PGJ-06 – 9 1/8" (23 cm)
  PGJ-12 – 16 3/8" (41 cm)
• 1/2" female inlet NPT
• Exposed diameter: 1 1/8" (3 cm)

Operating Specifications

• Discharge rate: .64 to 5.3 GPM (0.15 to 1.2 m3/hr; 2.4 to 20.1 l/min)
• Radius: 15' to 37' (4.6 to 11.3 m)
• Recommended pressure range: 30 to 50 PSI (2.1 to 3.4 bars; 206 to 344 kPa)
• Operating pressure range: 20 to 100 PSI (1.4 to 6.9 bars; 137 to 689 kPa)
• Precipitation rates: approximately 0.60" (16 mm) per hour at 40 PSI (2.8 bars; 275 kPa) for spacings from 16' to 37' (4.6 to 11.3 m)
• Nozzle trajectory: approximately 14°

Note: To ensure optimum nozzle performance; the rotor should be operated in the "Recommended pressure range." The sprinkler will work normally when used in the "Operating pressure range"; but nozzle performance may be reduced.